By the Way, this is a post I had over at somewhere else, but everyone stopped helping me.

Okay, well, as some of you know, I have a continuous error 21 with no disc in drive, can't access dashboard. So, I created an eeprom reader, from this site:http://forums.afterdawn.com/thread_view.cfm/357863
All connections are good, SCL to pin 13, SDA to pin 14 on LPC pad. When I turn on the xbox, the LED flashes orange 3 times, stops, flashes 4 times, stops, then flashes a final 5 times and shuts back down. Any suggestions?
By the way, I can't solder the wires to the EEPROM, the pins are way too small, and I'm not that great at soldering.

Grounded to Metal shield, but that shouldn't even matter should it? Ok, I have updated info. I took out SDA [14] on LPC, and I still get the orange LEDs. I took out the SCL [13] and it worked ok. I plugged back in the SDA [14] without SCL [13] and again, it worked perfectly. So the problem is SCL [13] apparently?

Ok, it wouldn't let me edit. Some other problems. In PonyPROG, what does Bus busy or hardware error (-11) mean? Also, I think I might've short-circuited the SCL [14] wire in my reader, because it sparked when I booted up my xbox. That might explain why my XBox doesn't do anything different when SCL is plugged in. But, shouldn't that mean that the whole circuit would be short-circuited? I'm not that great with wiring yet, I'm only 14.

How dare you call me a cracka. I think I'll hack into ****************. You should know what I'll do. Muwahahahaha

No, it's hacking. Go to any hacking forum and ask. Gaining access to any port using command prompt (DOS) using a shell account is considered hacking. Using it for malicious intent is cracking. Now, if you want me to go get a definition of it, I sure can. You want me to hack here? With Admin's permission of course.

Snipes: Don't even have a 360 yet.

No, it's definitly hacking, because you have to hack into ports on a web address in order to use it. I just figuered I'd go ahead and post it on any forum that I use with a computer section. Ghost Mail you say? I don't like using pre-made programs for hacking. If they have a site, ****************************************************************************************. You can guess what I'll do. muwahahahahhahaha

[I TAKE NO RESPONSIBILATY FOR WHAT READERS OF THIS SUBJECT MAY OR MAY NOT DO WITH WHAT THEY HAVE READ. IF YOU USE THIS INAPPROPIATELY, YOU WILL BE CAUGHT BY THE FBI OR POLICE AND SENT TO JAIL.]

Have you ever wanted to mess with your friends? Or just wanted to send a message to your kids from Santa or any other fake icon? (If you don't know Santa isn't real, please disregard the last sentence) Maybe just wanted to wreak some havoc and mail-bomb? (If you want to do this, this is not for you)
Before I start, I just want to say this.
I TAKE NO RESPONSIBILATY FOR WHAT READERS OF THIS SUBJECT MAY OR MAY NOT DO WITH WHAT THEY HAVE READ. IF YOU USE THIS INAPPROPIATELY, YOU WILL BE CAUGHT BY THE FBI OR POLICE AND SENT TO JAIL.
Now that that's over, let's get started. First and firmost, what you need to do is find a e-mail client on-line. (for example, yahoo.com, roadrunner.com, msn.com, etc.) For this example, I will be using roadrunner.com, because it's the only one that works for me. Second, you need an account to send to. For this example, I will use a "fake" account, (Yes, you can send mail to and from fake accounts.) "lord_hondros@hacking.com". Now, you will need an account to mail from. For this example, we'll use, "me@hacking.com". Now, go to "start", then "run". Click on it. (lol) type in "cmd" (without the quotes) and hit "enter". Next, type in "nslookup -querytype=mx XXXX", where XXXX is the e-mail client. By now, your command prompt should look like this-

Code:

Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.

C:\>nslookup -querytype=mx roadrunner.com

Then hit enter.
It should then give out a jumble of e-mail domains. We'll use mx.roadrunner.com
Next, type in "telnet mx.roadrunner.com 25", without the quotes. If you used something else, substitute that.
When you connect, you should get this-

Code:

220 aamta2.adelphia.net ESMTP server (InterMail vG.2.00.00.02 201-2161-108-103-2
0050713) ready Fri, 4 Jan 2008 12:28:23 -0500

Now, there is something you need to do every time you telnet. type in "helo", without the quotes. (From now on, assume you shouldn't put in quotes unless otherwise stated)
Now, you should get this-

Code:

220 aamta2.adelphia.net ESMTP server (InterMail vG.2.00.00.02 201-2161-108-103-2
0050713) ready Fri, 4 Jan 2008 12:28:23 -0500
helo
250 aamta2.adelphia.net

Now here's the fun part. Type in "MAIL FROM: me@hacking.com" This will set who the e-mail is from.
Now, wait a few seconds (unless you have dial-up, plan on taking a while), then it should say OK.
Type in "RCPT TO: lord_hondros@hacking.com" This will set who the e-mail is going to.
Now, do as instructed after the MAIL FROM. After it say's OK, type in the following-

DATA
(Wait a few seconds)
FROM: Me <me@hacking.com>
TO: lord_hondros <lord_hondros@hacking.com>
SUBJECT: I am hacking an e-mail account

Hello. I am typing a fake e-mail.
(Then type "." and hit enter)
Now, depending on your ISP, after a minute or two (or faster), it should confirm the message was sent. If not, you fubared up somewhere, or roadrunner just doesn't like you. You can also go ahead and enter any type of headers you think would make it look more real after the "SUBJECT" part. Hope it works for you, and remember, JUST BECAUSE YOU CAN DO SOMETHING, DOESN'T MEAN YOU SHOULD DO SOMETHING.

HAPPY HACKING!

p.s. If you want to use this, don't. I mean posting on another site anyways. If I find it, I'll hack you. But you can reword it, then post it if you want. Just try it out first.

AHHHHHHHH! You're so ********! Even if your PC sucks, you can still use it to boot up Xbox Hard drive Manager. As long as you have the EEPROM anyways. If you can wait till later, I'll find the tutorial for you.

Thanks, Yachi. And how was I advertizing? I didn't mean to.

Can't hot-swap. No EEPROM. And I've tried zzk's way of unplugging the hard drive before the X logo method. It doesn't work.

it wasn't really advertising. I don't even go their anymore.
I was banned from the forum, so I can't download it for you, but here's the link to the one on their site-
http://forums.halomods.com/viewtopic.php?t=63007
Um, just register an account and the link should be there.

It's not that hard if you can write programs and bridge connections. Then you can wreak a lot of havok on live. quite fun actually.

Okay, I need a way to mod an xbox, without using any money. You know, no softmod or hardmod. Something that I don't need to access my dashboard for. (still don't have my box fixed yet. Not enough money for a mod-chip. Maybe if someone could pitch in $40 or something... Hint hint...)

I don't mod on live unless I get a tip-off that someone is modding on matchmaking. Then I hack their gamertag, and ip address, join their game, beat them using my own mods, and finally upload a virus to their box cause they moded on live. Lot better than what Microsoft does.

Got to forums.halomods.com. They have a download for it in the section for halo2.

It probably isn't unless it was just the case.

go to google and type this in-

ump v3 site:forums.halomods.com

Hope it helps!

PS. Install it. Under one of the menus it should have visible projectiles or something.